Soundness of Cement | How to Keep Cement Sound

Soundness of Cement

To keep cement sound we need to be careful in some aspects. It is essential that a cement paste, once it has set, does not undergo a large change in volume. Such changes in volume may take place due to the delay in hardening cement, namely free lime, magnesia and calcium sulphate.

If the raw materials fed into the kiln contain more lime (CaO) than that can combine with the acidic oxides, the excess will remain in a free condition. The free lime will hydrate very slowly in a subsequent stage and the mortar and concrete prepared with such cement is therefore liable to expand and crack after a few months or a year. Cements which exhibit has expansion are known as unsound cements.

Cement can be unsound due to the presence of magnesia (MgO), which reacts with water in a manner similar to quick lime (CaO). However, only crystalline variety of magnesia (Periclasue MgO) is deleterious, but magnesia present in glass form is of course harmless.

Calcium sulphate is the third compound liable to cause expansion; in this case calcium sulpho-aluminate is formed. A hydrate of calcium sulphate-gypsum is added to cement clinker in order to prevent flash setting. But if gypsum is resent in excess of the amount that can react with C2A during setting, unsoundness in the form of a low expansion will result. For this reason, it is essential to limit very strictly the amount of gypsum that can be added to clinker, but the limits are well on the safe side as far as the danger of unsoundness is concerned.

Comments

Post a Comment

Popular posts from this blog

How To Calculate or Estimate Long-span Aluminium Roofing Sheets.

Image
Aluminium roofing sheets, they come in rolls of average of 600mm to 1300mm depends on the manufacture and specifications. As stated in previous articles, the aluminium sheets comes in rolls at the factory just like toilet rolls but with different widths and thickness based on specifications. Calculating the roof required could be done by calculating the surface area in square meters of the area covered by the aluminium and for some companies it could be calculated in meter lengths ,knowing the width which is 600mm above as constant. For a simple gable roof as shown in pic 1 with length of 25.2m. First you must know the height of roof from the section. For this sample we are taken the eight to be 3meters (10 feet)to know the length of leaf “x” or “y” Remember the pythagoras theorem x2=32 +6.12 x=6.8m Hence the area of roof is (6.8 i.e x)+6.8 i.e y) multiply by length 25.2m=342.72m2 If the width of the roof comes in 600mm or 0.6m, the length of the roof
Read more

Post Tension Slab – Advantages and Disadvantages of Post Tension Slab

Image
Post Tension Slab Although concrete is a strong material for construction, it is not resistant to breakdown especially where longer concrete slabs are required like in a bridge or a length of a beam. For this, the concrete slab is tensioned with a process called pre-stressing and the slab of concrete which comes out after this process is known as post tension slab. This slab is much stronger as well as more durable than the normal concrete slabs. In today’s world, where the modern engineering is finding new ways to build longer, more efficient and stronger structures, post tension slab becomes one of their chief requirements. There are many advantages and disadvantages of post tensioned slabs which we will discuss in this post. Advantages of Post Tension Slab Post tension slabs are advantageous in many ways. Some of the major benefits of post tension slabs are as follows. 1. Reduced cost: Post tension slabs are excellent ways to construct stronger structures at an affordable
Read more

How to install POP (plaster of paris) ceilling

Image
Plaster of Paris is regarded as any type of plaster containing calcined gypsum (calcium sulfate dihydrate), sand and water. When these ingredients are combined, they result in the formation of a tough, dry product; however, plaster of Paris can be sanded to achieve a variety of looks. By following some basic guidelines, you can use plaster of Paris to mend cracks, fix dents,for ceiling, in walls and even to create artworks. However in this case our focus is on ceiling. POP popularly called plaster of Paris is used for a lot of purposes because it can easily be formed to any shape and it hardens quickly and is easy to operate. To do a pop ceiling in your home, getting it done is in two ways, you can buy the materials yourself which include pop cement , yarn(sponge-like material) etc then pay the installer based on per square meter of area of coverage, or you can give it out totally as a contract. But these are the basic steps in getting pop ceiling cast-on-site done. Get cemen
Read more