How to Lay Bricks – Four Step Guide to Laying Bricks with Mortar


Many people often come to a common question how to lay bricks? Laying bricks is basically a systematic approach and it should be done with precision to provide enough strength to the construction. Bricks are considered as foundations of any establishments and thus, this job not only requires precision, but also needs sheer accuracy. When it comes to how to lay bricks, standard methods as well as the approaches are followed. No matter what kind of bricks you choose for the conduction job, brick laying process remains always the same for all cases. In the following section of this article, we shall have a look at the step by step guide to the brick laying process.

Step 1: First stage of Laying Bricks

At the first stage to lay bricks, you need to create a straight line, which is often referred as a mason’s line. This line is actually created by a thread from one end to another end. The first end of the thread should be your starting point for placing brick and the last end of the thread should be the ending point of laying bricks. Mason’s line helps setting the bricks in a perfectly straight line or row. To keep the thread intact and straight, you need a couple of bricks, each placed on the either ends of the thread. The top of each brick should touch the bottom of each brick. This will ensure that the bricks are placed evenly throughout. This is the most important part in brick laying process.


Step 2: Guide the Bricks

In your process of laying bricks, at the second phase, your story pole is a strip of wood that will act as the guide for laying bricks. Setting up this guide is important for seamless construction of the wall. Mistake in measurement or mistakes in this process may lead to inappropriate results at the end and eventually you will realize that you may have to make the whole construction once again right from the beginning. So, if you want to know how to lay bricks, know about guiding the bricks properly while laying them.


Step 3: Applying Mortar

To know how to lay bricks, you must have good knowledge to work with mortar. While working with mortar, it is important to wear rubber gloves for safety reasons. You have to use a spade trowel to apply mortar on every layer of the bricks. Spreading the mortar rightly and applying it generously will give the much needed strength to your construction.


Step 4: Remove Excessive Mortar

After applying the mortar, wait for a few minutes or continue brick laying for a few layers upside. Then, your next job is to remove the excessive mortar from both the ends of the wall. In the process of laying bricks, this is an important part as in this phase you are actually making the wall surfaces smoother.


These are the four steps that you have to follow for laying bricks. Well the process is easy, but accuracy as well as high end efficiency has been required to conclude this. Following the steps with precision will surely help you to know as well as learn how to lay bricks.

Comments

Post a Comment

Popular posts from this blog

How To Calculate or Estimate Long-span Aluminium Roofing Sheets.

Image
Aluminium roofing sheets, they come in rolls of average of 600mm to 1300mm depends on the manufacture and specifications. As stated in previous articles, the aluminium sheets comes in rolls at the factory just like toilet rolls but with different widths and thickness based on specifications. Calculating the roof required could be done by calculating the surface area in square meters of the area covered by the aluminium and for some companies it could be calculated in meter lengths ,knowing the width which is 600mm above as constant. For a simple gable roof as shown in pic 1 with length of 25.2m. First you must know the height of roof from the section. For this sample we are taken the eight to be 3meters (10 feet)to know the length of leaf “x” or “y” Remember the pythagoras theorem x2=32 +6.12 x=6.8m Hence the area of roof is (6.8 i.e x)+6.8 i.e y) multiply by length 25.2m=342.72m2 If the width of the roof comes in 600mm or 0.6m, the length of the roof ...
Read more

Post Tension Slab – Advantages and Disadvantages of Post Tension Slab

Image
Post Tension Slab Although concrete is a strong material for construction, it is not resistant to breakdown especially where longer concrete slabs are required like in a bridge or a length of a beam. For this, the concrete slab is tensioned with a process called pre-stressing and the slab of concrete which comes out after this process is known as post tension slab. This slab is much stronger as well as more durable than the normal concrete slabs. In today’s world, where the modern engineering is finding new ways to build longer, more efficient and stronger structures, post tension slab becomes one of their chief requirements. There are many advantages and disadvantages of post tensioned slabs which we will discuss in this post. Advantages of Post Tension Slab Post tension slabs are advantageous in many ways. Some of the major benefits of post tension slabs are as follows. 1. Reduced cost: Post tension slabs are excellent ways to construct stronger structures at an affordable...
Read more

How to install POP (plaster of paris) ceilling

Image
Plaster of Paris is regarded as any type of plaster containing calcined gypsum (calcium sulfate dihydrate), sand and water. When these ingredients are combined, they result in the formation of a tough, dry product; however, plaster of Paris can be sanded to achieve a variety of looks. By following some basic guidelines, you can use plaster of Paris to mend cracks, fix dents,for ceiling, in walls and even to create artworks. However in this case our focus is on ceiling. POP popularly called plaster of Paris is used for a lot of purposes because it can easily be formed to any shape and it hardens quickly and is easy to operate. To do a pop ceiling in your home, getting it done is in two ways, you can buy the materials yourself which include pop cement , yarn(sponge-like material) etc then pay the installer based on per square meter of area of coverage, or you can give it out totally as a contract. But these are the basic steps in getting pop ceiling cast-on-site done. Get cemen...
Read more