Swimming Pool Plaster Mix


Pool plaster mix refers to the finishing coat given to a concrete pool. Its purpose is to make the pool surface smooth and to provide a watertight seal. It also gives an aesthetic appeal. Approximately 0.25 to 0.5 inches thick plaster layer is used. White is the most common color, but other colors can be obtained by the application of pigmented aggregates. Proper maintenance is required to give a life of 20 years.

Ingredients

The pool plaster mix elements include, White Portland Cement along with aggregates such as limestone, quartz sand, marble dust, etc., in the ratio 1:2. Liquid acrylic concrete fortifier is needed to mix these constituents. It provides durability to the Pool Plaster Mix due to its constant immersion in water.

Maintenance of the mix

Pool plaster mix offers a higher expected life. In practical terms, it boils down to the maintenance and the water chemistry. Acidic conditions (low pH) etch the plaster, causing a pitted, rough surface leading to faster degradation. Alkaline conditions (high pH) cause scaling and later discoloring of the plaster. Copper, Iron or other minerals cause stains, while acid washing is a result of algal issues deteriorating the pool plaster mix.

Guidelines to produce an effective mix

As the plaster mix needs proper maintenance, a few guidelines are recommended. Using aggregates in the ratio of 1.5-1.75 to 1 part of cement is recommended. Using excess cement causes cracking, while excess aggregates reduce the durability of the pool plaster mix. A thick mix is often preferred. Both the Portland Cement Association (PCA) as well as the American Concrete Institute (ACI) recommends a maximum water-cement ratio of 0.48. In fact, they advise even lower ratios to withstand exposure to mild acids, increase density, reducing porosity, shrinkage and permeability.

Mixing more than 90 minutes must be avoided. The swimming pool plaster mix is best when it is used in the preparation. The mix should contain a minimum calcium chloride set-accelerant and not more than 2% white cement. Excess calcium chloride causes shrinkage and gray mottling discoloration.

Adding water to plaster surfaces should be avoided while troweling as it increases shrinkage, discoloration and porosity. Using a little water to lubricate the trowel does not have any profound effects on the quality of the pool plaster mix. Extreme weather conditions cause durability and quality issues. It is normal to finish plastering as soon as possible. However, plastering requires a minimum of 4 hours. Any plastering work done in less than this time is bound to have durability problems in the long run. The Pool Plaster Mix needs to dry for some time, before it is filled with water. The usual time is 6 hours, but the existing weather conditions play a significant role. An important point to be understood is that the bottom is the last portion to be plastered and hence, checking only the walls will not give a proper opinion. The last guideline of all is to keep the water pH level balanced. Excess acidic or alkaline conditions weaken the pool plaster mix.

Comments

  1. Grace Sutherland4 March 2020 at 11:03

    Hi there! Really love your blog and i was waiting since long to read such a informative post and i found yours, so keep it up.

    https://qualityplasterers.co.nz/

    ReplyDelete
  2. Laraib2 May 2021 at 02:55

    Your blog provided us with valuable information to work with. every tips of your post are awesome. Thanks a lot for sharing. Keep blogging, swimming pools waters

    ReplyDelete

Post a Comment

Popular posts from this blog

How To Calculate or Estimate Long-span Aluminium Roofing Sheets.

Image
Aluminium roofing sheets, they come in rolls of average of 600mm to 1300mm depends on the manufacture and specifications. As stated in previous articles, the aluminium sheets comes in rolls at the factory just like toilet rolls but with different widths and thickness based on specifications. Calculating the roof required could be done by calculating the surface area in square meters of the area covered by the aluminium and for some companies it could be calculated in meter lengths ,knowing the width which is 600mm above as constant. For a simple gable roof as shown in pic 1 with length of 25.2m. First you must know the height of roof from the section. For this sample we are taken the eight to be 3meters (10 feet)to know the length of leaf “x” or “y” Remember the pythagoras theorem x2=32 +6.12 x=6.8m Hence the area of roof is (6.8 i.e x)+6.8 i.e y) multiply by length 25.2m=342.72m2 If the width of the roof comes in 600mm or 0.6m, the length of the roof ...
Read more

Post Tension Slab – Advantages and Disadvantages of Post Tension Slab

Image
Post Tension Slab Although concrete is a strong material for construction, it is not resistant to breakdown especially where longer concrete slabs are required like in a bridge or a length of a beam. For this, the concrete slab is tensioned with a process called pre-stressing and the slab of concrete which comes out after this process is known as post tension slab. This slab is much stronger as well as more durable than the normal concrete slabs. In today’s world, where the modern engineering is finding new ways to build longer, more efficient and stronger structures, post tension slab becomes one of their chief requirements. There are many advantages and disadvantages of post tensioned slabs which we will discuss in this post. Advantages of Post Tension Slab Post tension slabs are advantageous in many ways. Some of the major benefits of post tension slabs are as follows. 1. Reduced cost: Post tension slabs are excellent ways to construct stronger structures at an affordable...
Read more

How to install POP (plaster of paris) ceilling

Image
Plaster of Paris is regarded as any type of plaster containing calcined gypsum (calcium sulfate dihydrate), sand and water. When these ingredients are combined, they result in the formation of a tough, dry product; however, plaster of Paris can be sanded to achieve a variety of looks. By following some basic guidelines, you can use plaster of Paris to mend cracks, fix dents,for ceiling, in walls and even to create artworks. However in this case our focus is on ceiling. POP popularly called plaster of Paris is used for a lot of purposes because it can easily be formed to any shape and it hardens quickly and is easy to operate. To do a pop ceiling in your home, getting it done is in two ways, you can buy the materials yourself which include pop cement , yarn(sponge-like material) etc then pay the installer based on per square meter of area of coverage, or you can give it out totally as a contract. But these are the basic steps in getting pop ceiling cast-on-site done. Get cemen...
Read more