Lath and Plaster – Cost Effective Methods To Repair Lath and Plaster


Lath and Plaster is one of the most preferred ways of finishing the internal surface of one’s home. It was a common method used in the 1950s, consisting of sawing or riveting thin strips of wood (laths). These strips are covered with plaster and leveled off. Just as with other things, they also require minor repairs to last for their expected years.


Cost effective methods

Short Term: Repairing Lath and Plaster in your home requires key decisions in the areas of time, budget and the final appearance required. The first choice is to remove dust by vacuuming and simply re-decorating with any suitable paint (preferably water based). However, this method is the best before the plaster starts to sag and crack. The cost is low and depends on the original condition of the plasterwork. Though this is best for cottages and buildings that exude an old-world charm, it is a short term solution and cannot give a ‘flat’ finish.

The next method is to scrape out the cracks and remove the loose material. The cracks are to be filled with decorators filler using a spreader. This is a cost effective method and maintains the ‘periodic’ feel giving a few more years to the initial condition.

Mid Term: Another preferred method of repairing Lath and Plaster is by gluing the plasterwork back to its place. Holes are to be drilled in the original plasterwork, the dust to be vacuumed out and adhesive needs to be injected. Supports are required at least until the adhesive is dry. The cost and time for this method depend on the extent of repairing to be carried out. A medium level of effectiveness is achieved, though it requires a specialist to do a proper job.

Exposing the beams is altogether a different method of dealing with Lath and Plaster. It requires removing of lath and plaster, de-nailing and disposing completely. All the plaster marks are to be brushed, wiring needs to be re-routed and other damages to be repaired. The beams can be left as they are or decorated with varnish or paint. This method involves a lot of work, especially in the removal and disposal of plaster and hence, the cost associated can be medium to high, again based on the work.

Long Term: Another suggested method to repair Lath and Plaster is to remove existing plasterwork and to re-apply three coats of plasterwork, two base coats and the finish coat. This is a costly and time consuming process requiring a specialist, but it is a long term solution and the finished work is as good as new. Another method is to support the plasterwork from below and remove loose debris, dust, etc. A new method to hold the lath (for example, wire mesh) may be used and the plasterwork re-applied. This is another long term plan to repair Lath and Plaster and an expensive one, but the period feel is maintained. This is used when the building is of historical importance.

Comments

Post a Comment

Popular posts from this blog

How To Calculate or Estimate Long-span Aluminium Roofing Sheets.

Image
Aluminium roofing sheets, they come in rolls of average of 600mm to 1300mm depends on the manufacture and specifications. As stated in previous articles, the aluminium sheets comes in rolls at the factory just like toilet rolls but with different widths and thickness based on specifications. Calculating the roof required could be done by calculating the surface area in square meters of the area covered by the aluminium and for some companies it could be calculated in meter lengths ,knowing the width which is 600mm above as constant. For a simple gable roof as shown in pic 1 with length of 25.2m. First you must know the height of roof from the section. For this sample we are taken the eight to be 3meters (10 feet)to know the length of leaf “x” or “y” Remember the pythagoras theorem x2=32 +6.12 x=6.8m Hence the area of roof is (6.8 i.e x)+6.8 i.e y) multiply by length 25.2m=342.72m2 If the width of the roof comes in 600mm or 0.6m, the length of the roof
Read more

Post Tension Slab – Advantages and Disadvantages of Post Tension Slab

Image
Post Tension Slab Although concrete is a strong material for construction, it is not resistant to breakdown especially where longer concrete slabs are required like in a bridge or a length of a beam. For this, the concrete slab is tensioned with a process called pre-stressing and the slab of concrete which comes out after this process is known as post tension slab. This slab is much stronger as well as more durable than the normal concrete slabs. In today’s world, where the modern engineering is finding new ways to build longer, more efficient and stronger structures, post tension slab becomes one of their chief requirements. There are many advantages and disadvantages of post tensioned slabs which we will discuss in this post. Advantages of Post Tension Slab Post tension slabs are advantageous in many ways. Some of the major benefits of post tension slabs are as follows. 1. Reduced cost: Post tension slabs are excellent ways to construct stronger structures at an affordable
Read more

How to install POP (plaster of paris) ceilling

Image
Plaster of Paris is regarded as any type of plaster containing calcined gypsum (calcium sulfate dihydrate), sand and water. When these ingredients are combined, they result in the formation of a tough, dry product; however, plaster of Paris can be sanded to achieve a variety of looks. By following some basic guidelines, you can use plaster of Paris to mend cracks, fix dents,for ceiling, in walls and even to create artworks. However in this case our focus is on ceiling. POP popularly called plaster of Paris is used for a lot of purposes because it can easily be formed to any shape and it hardens quickly and is easy to operate. To do a pop ceiling in your home, getting it done is in two ways, you can buy the materials yourself which include pop cement , yarn(sponge-like material) etc then pay the installer based on per square meter of area of coverage, or you can give it out totally as a contract. But these are the basic steps in getting pop ceiling cast-on-site done. Get cemen
Read more