Factors Affecting Choice Of Concrete Mix Design


Concrete mix design is defined as the appropriate selection and proportioning of constituents to produce a concrete with pre-defined characteristics in the fresh and hardened states. In general, concrete mixes are designed in order to achieve a defined workability, strength and durability .

The selection and proportioning of materials depends on:

. The structural requirements of the concrete
. The environment to which the structure will be exposed
. The job site conditions, especially the methods of concrete production, transport, placement, compaction and finishing
. The characteristics of the available raw materials

The various factors affecting the choice of concrete mix design are:

1. Compressive strength of concrete:

It is one of the most important properties of concrete and influences many other describable properties of the hardened concrete. The mean compressive strength required at a specific age, usually 28 days, determines the nominal water-cement ratio of the mix. The other factor affecting the strength of concrete at a given age and cured at a prescribed temperature is the degree of compaction. According to Abraham’s law the strength of fully compacted concrete is inversely proportional to the water-cement ratio.

2. Workability of concrete:

The degree of workability required depends on three factors. These are the size of the section to be concreted, the amount of reinforcement, and the method of compaction to be used. For the narrow and complicated section with numerous corners or inaccessible parts, the concrete must have a high workability so that full compaction can be achieved with a reasonable amount of effort. This also applies to the embedded steel sections. The desired workability depends on the compacting equipment available at the site.

3. Durability of concrete:

The durability of concrete is its resistance to the aggressive environmental conditions. High strength concrete is generally more durable than low strength concrete. In the situations
when the high strength is not necessary but the conditions of exposure are such that high durability is vital, the durability requirement will determine the water-cement ratio to be used.


4. Maximum nominal size of aggregate

In general, larger the maximum size of aggregate, smaller is the cement requirement for a particular water-cement ratio, because the workability of concrete increases with increase in maximum size of the aggregate. However, the compressive strength tends to increase with the decrease in size of aggregate. IS 456:2000 and IS 1343:1980 recommend that the nominal size of the aggregate should be as large as possible.

5. Grading and type of aggregate

The grading of aggregate influences the mix proportions for a specified workability and water-cement ratio. Coarser the grading leaner will be mix which can be used. Very lean mix is not desirable since it does not contain enough finer material to make the concrete cohesive.The type of aggregate influences strongly the aggregate-cement ratio for the desired workability and stipulated water cement ratio. An important feature of a satisfactory aggregate is the uniformity of the grading which can be achieved by mixing different size fractions.

6. Quality Control at site:

The degree of control can be estimated statistically by the variations in test results. The variation in strength results from the variations in the properties of the mix ingredients and lack of control of accuracy in batching, mixing, placing, curing and testing. The lower the difference between the mean and minimum strengths of the mix lower will be the cement-content required. The factor controlling this difference is termed as quality control.

Comments

Post a Comment

Popular posts from this blog

How To Calculate or Estimate Long-span Aluminium Roofing Sheets.

Image
Aluminium roofing sheets, they come in rolls of average of 600mm to 1300mm depends on the manufacture and specifications. As stated in previous articles, the aluminium sheets comes in rolls at the factory just like toilet rolls but with different widths and thickness based on specifications. Calculating the roof required could be done by calculating the surface area in square meters of the area covered by the aluminium and for some companies it could be calculated in meter lengths ,knowing the width which is 600mm above as constant. For a simple gable roof as shown in pic 1 with length of 25.2m. First you must know the height of roof from the section. For this sample we are taken the eight to be 3meters (10 feet)to know the length of leaf “x” or “y” Remember the pythagoras theorem x2=32 +6.12 x=6.8m Hence the area of roof is (6.8 i.e x)+6.8 i.e y) multiply by length 25.2m=342.72m2 If the width of the roof comes in 600mm or 0.6m, the length of the roof
Read more

Post Tension Slab – Advantages and Disadvantages of Post Tension Slab

Image
Post Tension Slab Although concrete is a strong material for construction, it is not resistant to breakdown especially where longer concrete slabs are required like in a bridge or a length of a beam. For this, the concrete slab is tensioned with a process called pre-stressing and the slab of concrete which comes out after this process is known as post tension slab. This slab is much stronger as well as more durable than the normal concrete slabs. In today’s world, where the modern engineering is finding new ways to build longer, more efficient and stronger structures, post tension slab becomes one of their chief requirements. There are many advantages and disadvantages of post tensioned slabs which we will discuss in this post. Advantages of Post Tension Slab Post tension slabs are advantageous in many ways. Some of the major benefits of post tension slabs are as follows. 1. Reduced cost: Post tension slabs are excellent ways to construct stronger structures at an affordable
Read more

How to install POP (plaster of paris) ceilling

Image
Plaster of Paris is regarded as any type of plaster containing calcined gypsum (calcium sulfate dihydrate), sand and water. When these ingredients are combined, they result in the formation of a tough, dry product; however, plaster of Paris can be sanded to achieve a variety of looks. By following some basic guidelines, you can use plaster of Paris to mend cracks, fix dents,for ceiling, in walls and even to create artworks. However in this case our focus is on ceiling. POP popularly called plaster of Paris is used for a lot of purposes because it can easily be formed to any shape and it hardens quickly and is easy to operate. To do a pop ceiling in your home, getting it done is in two ways, you can buy the materials yourself which include pop cement , yarn(sponge-like material) etc then pay the installer based on per square meter of area of coverage, or you can give it out totally as a contract. But these are the basic steps in getting pop ceiling cast-on-site done. Get cemen
Read more