Types Of Drawings By Structural Engineers


Types of Drawings prepared by Structural Engineers

There are four different types of drawing:

1) Structural Drawings
2) Reinforcement Drawings
3) Standard Details
4) Record Drawings

Structural Drawings:

Structural Drawings are used to progress the Architect’s concept by specifying the shape and position of all parts of the structure – thus enabling the construction of that structure on site. Structural Drawings are also used for the preparation of the reinforcement drawings.

Structural Drawings would typically include the following information:

. North Point
. Setting out dimensions for the concrete structure on site.
. Plans, sections and elevations showing layout, dimensions and levels of all concrete members within the structure.
. Location of all holes, chases, pockets, fixings and other items affecting the concreting work.
. Notes on specifications, finishes and all cross-references affecting the construction.
. Provide the detailer with the layout and sectional information required to specify the length, shape and number of each type of reinforcing bar.

Reinforcement Drawings:

Reinforcement drawings (or details), fully describe and locate all reinforcement in relation to the finished surface of the concrete and to any holes or fixings. They are primarily for the use of the steel fixers and it is preferable that they are kept separate from the general arrangement drawing.

As a general rule, circular holes up to 150mm diameter and rectangular holes up to (150 x 150)mm in slabs and walls need not to be shown on the reinforcement drawings.

For larger isolated holes with sides 500mm or less, either (i) displace affected bars either side of the hole,or (ii) cut or slide back affected bars a cover distance from face of the hole. Compensating trimming bars of equal area should be provided to trim all sides. These trimmers should extend a minimum 45? (Nominal anchorage length) beyond the hole. Holes in this category should be shown on the reinforcement drawings.

Standard Details:

The detailer will often find that certain details occur regularly on a variety of jobs and some economy in detailing time may be effected by keeping a library of “Standard Details” for use whenever possible. Standard details might include:-

1) Standard Notes

2) Column bases and pile caps

3) Concrete box culverts

4) Expansion/Construction joint details, etc.

Record Drawings:

It is common, in the course of construction, for modifications to be made to the original drawings to cater for unforeseen difficulties that inevitably occur on site.

Once the construction of a reinforced concrete structure is complete, the original drawings should be amended to show any changes in detail that were made during the construction process. Compared to manually produced drawings, amending drawings produced by computer is relatively easy.

A revision letter (suffix) must be added to the drawing number to indicate the drawing is a “record drawing”, and all amendments must be described in writing using this revision reference.

Comments

Post a Comment

Popular posts from this blog

How To Calculate or Estimate Long-span Aluminium Roofing Sheets.

Image
Aluminium roofing sheets, they come in rolls of average of 600mm to 1300mm depends on the manufacture and specifications. As stated in previous articles, the aluminium sheets comes in rolls at the factory just like toilet rolls but with different widths and thickness based on specifications. Calculating the roof required could be done by calculating the surface area in square meters of the area covered by the aluminium and for some companies it could be calculated in meter lengths ,knowing the width which is 600mm above as constant. For a simple gable roof as shown in pic 1 with length of 25.2m. First you must know the height of roof from the section. For this sample we are taken the eight to be 3meters (10 feet)to know the length of leaf “x” or “y” Remember the pythagoras theorem x2=32 +6.12 x=6.8m Hence the area of roof is (6.8 i.e x)+6.8 i.e y) multiply by length 25.2m=342.72m2 If the width of the roof comes in 600mm or 0.6m, the length of the roof
Read more

Post Tension Slab – Advantages and Disadvantages of Post Tension Slab

Image
Post Tension Slab Although concrete is a strong material for construction, it is not resistant to breakdown especially where longer concrete slabs are required like in a bridge or a length of a beam. For this, the concrete slab is tensioned with a process called pre-stressing and the slab of concrete which comes out after this process is known as post tension slab. This slab is much stronger as well as more durable than the normal concrete slabs. In today’s world, where the modern engineering is finding new ways to build longer, more efficient and stronger structures, post tension slab becomes one of their chief requirements. There are many advantages and disadvantages of post tensioned slabs which we will discuss in this post. Advantages of Post Tension Slab Post tension slabs are advantageous in many ways. Some of the major benefits of post tension slabs are as follows. 1. Reduced cost: Post tension slabs are excellent ways to construct stronger structures at an affordable
Read more

How to install POP (plaster of paris) ceilling

Image
Plaster of Paris is regarded as any type of plaster containing calcined gypsum (calcium sulfate dihydrate), sand and water. When these ingredients are combined, they result in the formation of a tough, dry product; however, plaster of Paris can be sanded to achieve a variety of looks. By following some basic guidelines, you can use plaster of Paris to mend cracks, fix dents,for ceiling, in walls and even to create artworks. However in this case our focus is on ceiling. POP popularly called plaster of Paris is used for a lot of purposes because it can easily be formed to any shape and it hardens quickly and is easy to operate. To do a pop ceiling in your home, getting it done is in two ways, you can buy the materials yourself which include pop cement , yarn(sponge-like material) etc then pay the installer based on per square meter of area of coverage, or you can give it out totally as a contract. But these are the basic steps in getting pop ceiling cast-on-site done. Get cemen
Read more